Shoppingpc.net

Fluke Networks EtherScope Series II เครื่องตรวจซ่อมระบบ LAN ทั้งแบบใช้สายและไร้สาย

฿0.00
Fluke Networks EtherScope Series II เครื่องตรวจซ่อมระบบ LAN ทั้งแบบใช้สายและไร้สาย
เหลือ 0 ชิ้น
  • หมวดหมู่ : Fluke
  • รหัสสินค้า : 001825

รายละเอียดสินค้า Fluke Networks EtherScope Series II เครื่องตรวจซ่อมระบบ LAN ทั้งแบบใช้สายและไร้สาย

Fluke Networks EtherScope Series II เครื่องตรวจซ่อมระบบ LAN ทั้งแบบใช้สายและไร้สาย

 

EtherScope™ Series II เป็นเครื่องมือขนาดพกพาสำหรับงานติดตั้งและตรวจซ่อมระบบเครือข่าย 10, 100 และ Gigabit ทั้งชนิดสายเคเบิ้ล และชนิดไร้สาย

ช่วยในการติดตั้งระบบเครือข่าย LAN และ Wi-Fi ทำได้ภายในเวลาและงบประมาณที่กำหนด ใช้ทดสอบระบบระหว่างติดตั้งและการอัพเกรด

มีความสามารถตรวจค้นและแก้ไขปัญหาของระบบเครือข่ายที่หน้างานได้อย่างรวดเร็ว ด้วยความฟังค์ชั่นอำนวยความสะดวกที่เพียบพร้อมในตัว

คุณสมบัติ

  • ค้นหาอุปกรณ์ในเครือข่ายได้ถึง 1000 Device รวมถึงค้นหา VLANs, access points, mobile clients และอื่นๆ
  • ช่วยในการวิเคราะห์ระบบ Network สามารถบันทึกและแก้ปัญหาได้อย่างสะดวกรวดเร็ว นำไปใช้ได้ทุกสถานที่
  • แก้ปัญหาในเรื่องของ traffic สายสัญญาณ cable และ wireless
  • ค้นหา access points ทุกตัว บอก Signal และ noise แต่ละตัว และแต่ละ ช่องความถี่ (Site Survey WLAN)
  • สามารถเข้าไปดูค่า Configuration ของอุปกรณ์ต่างๆได้
  • ทดสอบ throughput ในเครือข่ายได้ และสามารถจำลองสร้างทราฟิกเข้าไปในเครือข่ายได้
  • ตรวจสอบความยาวสาย short, open, PoE และสัญญาณที่วิ่งผ่านสายแต่ละเส้นได้
  • สามารถ Monitor network traffic และ switch interfaces ได้โดยใช้ SNMP
  • สามารถระบุ Top client, Top AP ได้
  • สามารถสรุปรายงานเป็นกราฟิก GUI ทำรายงานแบบกราฟและแผนภูมิได้
  • สามารถส่ง Tone ใช้กับ Intellitone Pro 200 Probe เพื่อใช้ในการค้นหาปลายสาย
  • รองรับ 10/100 ,Gigabit Ethernet และ Wireless

Fluke Network รุ่น EtherScope Network Assistant เป็นเครื่องมือวิเคราะห์ระบบ Network ขนาดกระทัดรัด สำหรับ Gigabit LAN และ Wireless LAN

- เป็นเครื่องมือที่สามารถ Auto Discovery 1000+ devices, network, VLANs, access points, mobile clients และอื่นๆ

- เป็นเครื่องมือที่ช่วยวิเคราะห์ระบบ Network ขนาดกระทัดรัดที่ช่วยให้คุณสามารถบันทึกและแก้ปัญหาได้อย่างสะดวกรวดเร็ว นำไปใช้ได้ทุกสถานที่

- เป็นเครื่องมือที่ช่วยแก้ปัญหาในเรื่องของ traffic เรื่องของสาย cable, wireless

- เป็นเครื่องมือที่สามารถมองเห็น access points ทุกตัว และบอก Signal และ noise แต่ละตัว และแต่ละ ช่องความถี่ (Site Survey WLAN)

- สามารถเขาไปดูค่า Configuration ของอุปกรณ์ต่างๆได้

- สามารถทำการทดสอบ throughput ในเครือข่ายได้ และสามารถจำลองสร้างทราฟิกเข้าไปในเครือข่ายได้ - สามารถตรวจสอบความยาวสาย short, open, PoE และสัญญาณที่วิ่งผ่านสายแต่ละเส้นได้

- สามารถ Monitor network traffic และ switch interfaces ได้โดยใช้ SNMP

- สามารถระบุ Top client, Top AP ได้

- สามารถสรุปรายงานเป็นกราฟิก GUI ทำรายงานแบบกราฟและแผนภูมิได้

- สามารถส่ง Tone ใช้กับ Intellitone Pro 200 Probe เพื่อใช้ในการค้นหาปลายสาย

- รองรับ 10/100 ,Gigabit Ethernet และ Wireless

Specifications
General Specifications
Weight, with battery 0.86 kg (1.9 lb)
Dimensions 19.1 x 15.2 x 4.4 cm (7.5 x 6.0 x 1.75 in)
Display LCD touch screen, 640 x 480 pixels, TFT (active) color panel, touch pad
LED indicators 6 (including power LED)
Carrying Case Rugged carrying case for mainframe and standard accessories


Power
Battery Lithium Ion 7.2V DC (nominal), 4.2Ah, removable/rechargeable
Battery life 4 hour typical, 10 hour in standby mode
External AC adapter/battery charger AC input: 90 to 264 V ac, 48 to 62 Hz; 1.5 A
  DC output: 15 V dc, 1.2 A (isolated output)
Auto Charger 12V “cigarette lighter” charger with 6 foot (1.8 m) fully extended coiled cord and LED power indication


Ports
Communication and accessory ports 1 USB (supports out-of-band NIC for remote control), 1 PCMCIA/Cardbus (PC Card type II), 1 SFP cage, 1 CompactFlash (Card Type I/II), 1 DB-9 serial, headphone jack, microphone jack, Kensington lock receptacle
RJ-45 / Copper Port RJ-45 10/100/1000BASE-T Ethernet.
LAN option must be enabled to activate the copper port.
Fiber Port Small Form-factor Pluggable (SFP) in accordance with MSA.
Fiber option must be enabled to activate the fiber port.
Supported SFP Modules 1000BASE- LX, SX, ZX, BX, 100BASEFX.
Transceiver models MS-SX, MS-LX, and MS-100FX require EtherScope software version 4.0 or higher.
SFP Connector Duplex LC


Environmental and safety
Operating Temperature 0° to +50°C (32° to 122°F) with up to 95% relative humidity
Battery Charging 10° to +40°C (50° to 104°F) with up to 95% relative humidity
Temperature  
Storage temperature -20° to +60°C (-4° to 140°F)
Shock and vibration Meets requirements of MIL-PRF-28800F for Class 3 equipment
Safety CSA Canada and United States, CE, FCC Part 15 Class A, C-TICK N10140; UL and CSA approvals for universal AC adapter.
EMC Complies with EN61326, Class A, Criteria C


Copper media
Cable types Unshielded twisted pair LAN cables (100 and 120 Ohm UTP)
  Foil-screened twisted pair LAN cables (100 and 120 Ohm ScTP)
Cable length 1 to 305 m (3 to 1000 ft), accuracy dependent upon the cable type selected
Length resolution ± [5% of reading + 1 m (3 ft)], with open, shorted, with wire map adapter, or terminated with reflection = 20%
Receive level 100 to 5000 mVp-p
Datalink signal 500 to 4000 mVp-p
Measuring terminated cables The Cable Verification feature tests the individual twisted-pairs of a cable that are terminated into most equipment vendor's Ethernet ports such as on a hub, switch or NIC. All cable tests other than WireView wire map and office locator ID are operational in the presence of datalink signal.
Wiremapper/office locator compatibility Detects combinations of shorts, opens, and connector miswires. Compatible with Fluke Networks WireView wire map adapter/office locator.
Fault tolerance The RJ-45 Ethernet connection on the analyzer is designed to withstand a maximum of 100 volts.


Fiber optic power measurements
Receive Input Power, Transmit Output Power, Temperature, Voltage, TX Bias Current Real time access to digital diagnostic monitoring of SFP operating parameters in accordance with the SFP Multi Source Agreement (MSA) and SFF-8472.


ProVision™ Tests
Compatible remote devices EtherScope, MetroScope, LinkRunner PRO/Duo with reflector, layer 1 loopback, 802.3ah device
Note: An EtherScope with v5 software or a LinkRunner Duo is required for 16K jumbo frame testing.
Test Configuration Each test may be made up of an unlimited number of suites which run sequentially. Each suite may measure a maximum of eight streams total (including upstream and downstream) from one to four peer devices or a maximum of four streams (roundtrip) from one to four reflectors.
Test Duration Each suite can run for any length of time from 1s to 24h. Suites may be run sequentially for virtually unlimited test lengths.
Tests Throughput, Latency, Jitter, Loss/BERT, measured in parallel
Application port User defined, per stream
Frame content All 0s, all 1s, alternating 1s and 0s, Pseudo Random Bit Sequence (PRBS), Incrementing Byte, HFPAT, LFPAT, MFPAT, LCRPAT, SCRPAT
Frame size 48, 64, 128, 256, 512, 1024, 1280, 1518, 2024, 9000, RFC-2544 sweep, Jumbo sweep, or user-defined including jumbo sizes up to 16000
Rate (bps) Up to 1000 Mbps (selectable per stream)
802.1Q settings VLAN Id, QoS with CoS and ToS , QinQ VLAN Id, priority for each individual stream or all streams. Programmable TPID, DEI, CFI and VID for all streams
IP TOS settings IP Precedence/TOS parameter, DiffServe Code Point
Pass/Fail Limits Throughput (separate upstream and downstream), Latency, Jitter, Loss/BERT
Summary Display Summary matrix of all streams and all measurements; IP/Mac addresses, VLANPriority/TOS, status,Tx and Rx rates in bps and fps, frames sent and lost, loss ratio, errored intervals; current, average, maximum latency and jitter.
Detailed Display Individual measurements may be shown in tabular (by frame size), graphical (by frame size) or trending (by current interfal or total test duration for all frame sizes).
Frame Loss Statistics Total, current, and maximum for: frames sent and lost, loss ratio, BER, errored intervals, severely errored intervals
Data Export Throughput, Frames Sent/Received, Loss, Delay and Jitter test results for each stream are time stamped and saved to the CD card once per measurement interval for the duration of the test.


RFC 2544 Performance Tests
Compatible remote devices EtherScope, MetroScope, LinkRunner PRO/Duo with reflector, layer 1 loopback, 802.3ah device
RFC-2544 Compliant Tests Throughput, Latency, Frame Loss, Back-to-Back
Additional Performance Tests Loss Rate, Jitter, FrameBERT
Frame content All 0s, all 1s, alternating 1s and 0s, Pseudo Random Bit Sequence (PRBS), Incrementing Byte, HFPAT, LFPAT, MFPAT, LCRPAT, SCRPAT
Frame size 64, 128, 256, 512, 1024, 1280, 1518, 9000, RFC-2544 sweep, Jumbo sweep, or user-defined including jumbo sizes up to 16000
Application port User defined
Rate (bps) Up to 1000 M
802.1Q settings VLAN Id, priority
IP TOS settings IP Precedence/TOS parameter, DiffServe Code Point
Throughput settings Duration, maximum rate, measurement accuracy, pass/fail limits
Latency settings Duration, rate, iterations, pass/fail limits
Frame loss settings Duration, rate, step size, pass/fail limits
Frame loss settings Duration, rate, step size, pass fail
Back to Back settings Min and Max duration, rate, iterations, pass/fail limits
Loss Rate Duration, rate, pall/fail limits
Jitter Settings Duration, rate, pass/fail limits
FrameBERT Settings Duration, rate, pass/fail limits


Server Response Tool
TCP Port Response DNS Name, IP address, port name, port number, port responsiveness
TCP Trace Route Hop Count, router name, IP address, average RTT and percentage of total RTT


Internetwork Throughput Option
Compatible remote device EtherScope, MetroScope, LinkRunner PRO/Duo with reflector option, OptiView v3 Integrated Network Analyzer, OneTouch Series II
Frame content All 0s, all 1s, alternating 1s and 0s, Pseudo Random Bit Sequence (PRBS)
Frame size 64, 128, 256, 512, 1024, 1280, 1518, sweep of all sizes
Rate (bps) 12336 to 1000 M
Duration(s) 1 to 64,800 (18hr)
Results Frames sent, received, rate and percent loss for both upstream and downstream directions
Results format Tabular, graphical, xml-based report


Traffic generator
Traffic type Broadcast, multicast or unicast, FCS errors
Frame type Layer 1 FLUKE, Layer 2 FLUKE, Layer 3 FLUKE, Benign Ethernet, Benign LLC, NetBEUI, Benign IP, IP/ICMP Echo, IP/UDP Echo, IP/UDP Discard, IP/UDP Chargen, IP/UDP NFS, IP/UDP NetBIOS
Frame size 48, 64, 128, 256, 512, 1024, 1280, 1518, 9000, user defined up to 16000B
Rate Utilization (%): >0 – 100, Frames/second: 1 – 1488095
Duration Seconds: 1 – continuous, Frames: 1 – continuous


Service Performance Tool

Category of devices tested
DHCP Servers, DNS Servers, E-mail Servers (SMTP, POP3), FTP Servers, NT File Servers, Web Servers, WINS Servers, User-Defined Servers
Test controls Iterations, interval
Add device by IP address or host name (except Web Server where URL added)
DHCP Server pass/fail criteria Ping response time, server response time
DHCP Server BOOTP parameters (optional) Subnet mask, domain server, WINS server, NetBIOS scope, POP3 server, router/default gateway, client DNS domain, NetBIOS node type, SMTP server, web server
DNS Server pass/fail criteria Ping response time, server response time
E-mail Server pass/fail criteria Ping response time, SMTP SYN/ACK response time, SMTP response time, POP3 SYN/ACK response time, POP3 response time
E-mail Server operation modes Connect only, log in only, send/receive
FTP Server pass/fail criteria Ping response time, SYN/ACK response time, connect time, disconnect time, delete file time, write rate, read rate
FTP Server operation modes Server response, read, write/read/delete
NT File Server pass/fail criteria Ping response time, SYN/ACK response time, connect time, disconnect time, delete file time, write rate, read rate
NT File Server operation modes Server response, read, write/read/delete
Web Servers pass/fail criteria Web Server name lookup time, ping response time, SYN/ACK response time, first reply time, receive time, receive rate
WINS Servers pass/fail criteria Ping response time, server response time
User-Defined Servers pass/fail criteria Ping response time, SYN/ACK response time
Results format Tabular, graphical, xml-based report


802.3ah Client
Functions Remote device discovery, loop-up with 1s keep-alive, loop down. May be run in background while other MS functions are active.
Display Loopback capability of remote, OAM status OAM mode link status, maximum OAM size, remote state


IPTV Tests
Configuration Multicast Group IP, Port Number, join, leave, RTSP URL, setup, play, pause, teardown
Results IGMP Latency, Total Packets Sent, Connected Time, Received Packet Rate, RFC-4445 MDI Delay Factor and Media Loss Rate for MPEG-2 streams

Instrument Settings
TCP/IP DHCP, static
Management TCP/IP DHCP, static (management using USB Ethernet adapter purchased separately)
802.1Q LAN: S-VLAN, C-VLAN, TPID, Priority, DEI, VID
IP Type Of Service (TOS) LAN: IP precedence, DSCP
Security LAN: 802.1X
WLAN: 802.1X, WEP, WPA PSK, 802.11i PSK, WPA, WPA2
802.1X EAP type TLS, GTC, MD5, MSCHAPV5, PEAP GTC, PEAP MD5, PEAP MS-CHAP-V2, PEAP TLS, TTLS PAP, TTLS CHAP, TTLS MSCHAP, TTLS MSCHAP-V2, TTLS EAP-MD5, TTLS EAP-GTC, TTLS-EAP-MSCHAP-V2, TTLS EAP-TLS, EAP FAST
Active tests LAN: User defined tests to appear on detailed view home page and drop down navigation
SNMP LAN: v1, v2, v3 (with SHA and MD5 authentication, DES encryption)
Ethernet LAN: Auto-negotiation, force setting, MAC address
Instrument security Password control for remote UI, ProVision and RFC2544 tests, SNMP settings, and 802.1X
General Enable as remote, advanced remote NAT/Proxy settings, user preferences
Group names WLAN: assign alias to one or more devices

Tools
LAN Ping, trace route, trace switch route, traffic generator, web browser, telnet, SSH telnet, terminal, FTP, TFTP, xDP port reporter (CDP, LLDP), Service Performance Tool, Remove CF Card, Lock Screen, Report
WLAN Ping, trace route, web browser, telnet, SSH telnet, terminal, FTP, TFTP, wireless throughput, report

Wireless LAN Adapter Card
Specification compliance IEEE 802.11a, 11b, 11g
Certifications FCC part 15, Telec, CTICK, ETSI, EN301893, EN60950
Interoperability WECA Compliant
Interface 32-bit Cardbus
Outdoor operating range Up to 515 m (1690 ft)
Indoor operating range Up to 85 m (279 ft)
Data rate 802.11a: up to 54 Mbps, 802.11b: up to 11 Mbps, 802.11g: up to 54 Mbps
Output power 18 dBm peak power
Infrastructure mode BSS
External antenna connector jack Hirose MS-147

Wireless LAN Directional Antenna
Frequency range 2.4 – 2.5 and 4.9 - 5.9 GHz
Minimum gain 5.0 dBi in the 2.4 GHz band and 7.0 dBi in the 5 GHz band
External antenna connector plug Hirose MS-147
 
สินค้า By order 15-20 วัน

 

088-2740600ติดต่อฝ่ายขาย

088-2740601

088-2740602

088-2740603

สนใจติดต่อบริษัท ชอปปิ้งพีซี ดอทเน็ต จำกัด

โทร ... 02-933-0022 , 081-318-9844

สินค้าที่เกี่ยวข้อง Fluke Networks EtherScope Series II เครื่องตรวจซ่อมระบบ LAN ทั้งแบบใช้สายและไร้สาย